This screw is used to attach the grips to the grip frame of markers of the brands: Luxe (TM40, X, ICE, OLED, 2.0 and older), Shocker (ERA, AMP, XLS and RSX), GOG (eNMEy, eNVy and older), AKA markers (depending on the thickness of the grips) and Smart Parts markers (depending on the thickness of the grips). Please compare with the respective manual of the marker.  

GOG cal.50 eNMEy Spare Part Factory part:NM5111 NME 50CAL Ball DetentThe ball detent of the GOG cal.50 eNMEy  

The original barrel that comes with the eNMEy here as spare part.It is about 10 inches (25 cm) long.Inner diameter: caliber .50 "  

GOG cal.50 eNMEy Spare Part Factory part:NM5109 NME 50CAL BoltThe bolt of the GOG cal.50 eNMEy  

GOG cal.50 eNMEy Spare Part Factory part:NM5110 NME 50CAL Bolt StopThe bolt stopper is the central component in the bolt of caliber 50 eNMEy to separate the two pressure areas.  

GOG cal.50 eNMEy Spare Part Factory part:NM5112 NME 50CAL Breach InsertThe breach insert of the GOG cal.50 eNMEy  

The GOG Ball Detent in a kit of 2. The two ball detents prevent several balls from entering the feed during the reloading process. To experience, the detents are subject to increased wear so that they should be regularly checked for wear signs and if necessary they must be replaced. A missing or damaged ball detent will inevitably lead to ball breaks. A set of spares should be in every gearbag.Generation 3: spring-loaded Delrin BalldetentCompared to the normal "rubber balldetents", the generation 3 balldetents reach deeper into the breach to hold even small paintballs.Compatible with: eNMEy, eNVy, ION, ION XE, EOS, Epiphany, SP-1, SP-8, Vibe  

The original barrel that comes with the eNMEy here as spare part.It is about 10 inches (25 cm) long.Inner diameter: caliber .68 "  

The eNMEy Bolt Rear Assembly for caliber .68" eNMEy consists of the two parts NM6104 and NM6105.Original manufacturer part  

This eNMEy caliber conversion kit enables you to change the caliber of your eNMEy. This kit contains everything you need for the conversion:- complete bolt- Barrel in the correct diameterWith this set you can convert a caliber .50" eNMEy into a caliber .68" eNMEy.Only compatible zu "generation 2" eNMEys "tooless bolt removal markers".This set can also be used as spare parts for existing caliber .68" eNMEys, since it includes the complete bolt and barrel in the correct diameter.  

This solenoid is the main valve, version 2, which can be installed in the eNMEy from the 2nd generation (after approx. 2017). The new version of the valve is reinforced with a metal plate and is therefore even more stable than the standard valve. If something breaks, you can replace the valve easily and inexpensively. The hoses and mounting brackets are already included in this set to ensure the easiest possible installation.  

This screw set for the GOG eNMEy marker contains all parts that can be lost in daily operation. Therefore, we recommend this set to every player.Also compatible with the SmartParts marker eNVy, G-1, SP-1 und Vibe..  

This seal kit for the GOG eNMEy marker contains all relevant O-rings for the repair of your marker. Also compatible with the SmartParts marker eNVy, G-1, SP-1 and Vibe.  

GOG eNMEy spare part Factory part: NME304 HE Valve Actuator PinThe actuator pin is located in the gripframe and is the connection between the trigger and the valve.This is the version for the High Efficiency Valve.  

GOG eNMEy spare part Factory part: NME204 Actuator PinThe actuator pin is located in the gripframe and is the connection between the trigger and the valve.This is the version 2 (MK2) for "valve, mk2" with the metal plate on the outside.  

GOG eNMEy spare part Factory part: ENV122 barb tower screwThis screw connects the valve assambly to the body of the eNMEy.Uses twice in the marker, once at the back connector and in the middle on the short barb.Will fit eNNY/G1 markers with the round barb connector as well (not eXTYy with the square connector).  

This is the original body in the first version of the SmartParts eNMEy as a spare part. The housing is delivered without a breech assembly and is available in different colors in order to be able to distinguish between the markers during play or to customize them. Due to its longer storage period, we are offering this spare part at a reduced price.  

This is the original body of the GOG eNMEy as a spare part. The housing is delivered without Breech assembly.It is available in different colors to differentiate the markers during gameplay (team marking) or to habe an individual design.  

The eNMEy Bottom Line ASA is the "Air Source Adapter" for the eNMEy.It will accept regular presets as well as CO2 bottles.It is afixed to the gripframe via two screws.  

GOG eNMEy spare part Factory part: SSB002 Bottom-line screwThis screw fixes the Bottom-line pannel to the grip frame. Two are needed for a marker.  

This is the original feedneck of the GOG eNMEy, also suitable for the SmartParts eNVy.If the feedneck is broken, you will be happy about he original spare part for your marker.Delivery is feedneck with screws.  

GOG eNMEy spare part Factory part: SSB009 grip panel screwThis screw fixes the grip pannel to the grip frame. Four are needed for a marker.  

This is the nut NUT003 for the eNMEy Feedneck ENV115. It can happen that the nut is lost, Here you can get the original nut as a spare part  

The eNMEy rubber grips.